首页 > 其他 > 详细

Huawei-R&S-网络工程师实验笔记20190615-IP基础(AR201上配置IP)

时间:2019-06-16 09:58:32      阅读:313      评论:0      收藏:0      [点我收藏+]

》Huawei-R&S-网络工程师实验笔记20190615-IP基础(AR201上配置IP)

》》实验开始,先上拓扑图参考:

技术分享图片

》》》一般正常配置IP操作如下,问题在于无法继续:

[AR1]int e0/0/0
[AR1-Ethernet0/0/0]ip address 192.168.1.1 24
                      ^
Error: Unrecognized command found at ^ position.
[AR1-Ethernet0/0/0]

》》》》这是怎么回事呢?原来eNSP上对AR201这款路由器只设定了Ethernet接口,而且本来eNSP就对Ethernet接口定义了二层接口功能,故而无法配置IP。解决办法也是有的,两种方案可以成功:
1、在eNSP中直接换个型号,除了AR201其他型号都有GE口,都可以配置IP地址。
2、坚持AR201的话,可采用vlan方案,该方案又有两种模式,具体如下:

[AR1]vlan 10
[AR1-vlan10]int vlan 10       //务必进入vlanif配置
[AR1-Vlanif10]ip address 1.1.1.1 255.255.255.0       
[AR1-Vlanif10]quit 
[AR1]
[AR1]interface Ethernet0/0/0                  //先试试Access方案

[Huawei-Ethernet0/0/0]port ?
  default    Specify current ports PVID VLAN characteristics
  link-type  Switch port link type
  priority   Specify current ports priority

[AR1-Ethernet0/0/0]port link-type access        //配置为Access模式
[AR1-Ethernet0/0/0]port default vlan 10       //Access下可以通过vlan10

[AR1]dis ip int bri
*down: administratively down
^down: standby
(l): loopback
(s): spoofing
The number of interface that is UP in Physical is 2
The number of interface that is DOWN in Physical is 1
The number of interface that is UP in Protocol is 2
The number of interface that is DOWN in Protocol is 1

Interface                         IP Address/Mask      Physical   Protocol  
Ethernet0/0/8                     unassigned           down       down      
NULL0                             unassigned           up         up(s)     
Vlanif10                          192.168.1.1/24       up         up      //IP配置成功了   
[AR1]
[AR1]int e0/0/0     //其实,不管是Access还是Trunk都是为了E0/0/0接口可以连通其他设备,纯粹配置IP是没有意义的。现在我们开始Trunk方案。

[AR1-Ethernet0/0/0]port link-type trunk    //前面不是设置成Access了嘛,想直接改是不行的
Error: Please renew the default configurations.

[AR1-Ethernet0/0/0]undo port default vlan       //得先取消vlan配置(如果在trunk前提下改Access,怎么改?命令是什么?)
Jun 16 2019 00:16:21-08:00 AR1 %%01IFNET/4/IF_STATE(l)[0]:Interface Vlanif10 has
 turned into DOWN state. 

[AR1-Ethernet0/0/0]port link-type trunk     //现在设置trunk就没问题了
[AR1-Ethernet0/0/0]port ?
  link-type  Switch port link type
  priority   Specify current ports priority
  trunk      Trunk port
[AR1-Ethernet0/0/0]port trunk ?       //这两种都试一下,先试试PVID
  allow-pass  Allowed vlan
  pvid        Specify current ports PVID VLAN characteristics

[AR1-Ethernet0/0/0]port trunk pvid vlan 10
[AR1-Ethernet0/0/0]dis ip int bri    
[AR1-Ethernet0/0/0]q
[AR1]q
<AR1>ping 192.168.1.2
  PING 192.168.1.2: 56  data bytes, press CTRL_C to break
    Request time out
  --- 192.168.1.2 ping statistics ---
    5 packet(s) transmitted
    0 packet(s) received
    100.00% packet loss       //PVID不通,再试试allow-pass

[AR1]int e0/0/0
[AR1-Ethernet0/0/0]port trunk allow-pass vlan 10
Jun 16 2019 00:22:39-08:00 AR1 %%01IFNET/4/IF_STATE(l)[2]:Interface Vlanif10 has
 turned into UP state. 
[AR1-Ethernet0/0/0]q
[AR1]dis ip int bri
*down: administratively down
^down: standby
(l): loopback
(s): spoofing
The number of interface that is UP in Physical is 2
The number of interface that is DOWN in Physical is 1
The number of interface that is UP in Protocol is 2
The number of interface that is DOWN in Protocol is 1

Interface                         IP Address/Mask      Physical   Protocol  
Ethernet0/0/8                     unassigned           down       down      
NULL0                             unassigned           up         up(s)     
Vlanif10                          192.168.1.1/24       up         up        
[AR1]q

<AR1>ping 192.168.1.2
  PING 192.168.1.2: 56  data bytes, press CTRL_C to break
    Reply from 192.168.1.2: bytes=56 Sequence=1 ttl=255 time=320 ms
    Reply from 192.168.1.2: bytes=56 Sequence=2 ttl=255 time=30 ms
    Reply from 192.168.1.2: bytes=56 Sequence=3 ttl=255 time=10 ms
    Reply from 192.168.1.2: bytes=56 Sequence=4 ttl=255 time=20 ms
    Reply from 192.168.1.2: bytes=56 Sequence=5 ttl=255 time=10 ms

  --- 192.168.1.2 ping statistics ---
    5 packet(s) transmitted
    5 packet(s) received
    0.00% packet loss
    round-trip min/avg/max = 10/78/320 ms                       //这时候就能ping通了
<AR1>

 

 

 

 

未完待续。。。

 

Huawei-R&S-网络工程师实验笔记20190615-IP基础(AR201上配置IP)

原文:https://www.cnblogs.com/ict-tang/p/11029497.html

(0)
(0)
   
举报
评论 一句话评论(0
关于我们 - 联系我们 - 留言反馈 - 联系我们:wmxa8@hotmail.com
© 2014 bubuko.com 版权所有
打开技术之扣,分享程序人生!